Trumpeter

Item #208 Includes full detailed interior torsion bar, separated suspension, folding side platform, optional long exhaust pipes, elevating main gun, optional 60cm and 54 cm barrel with rifling and shells, also include railway. Markings for Nr. I "Adam"...

Includes detailed exterior, metal axles, and photo-etched parts.

This giant locomotive was used for, among other purposes, hauling the Leopold and Karl guns to firing positions during the war. As a prime target of the allies, it was constructed with heavily armored side plates to protect its boiler, engineer and...

Includes 900mm (approx 35.5 inches) of track

Includes: Both initial and late chassis Artillery crew (8 figures) Two metal shells (aluminum)

The German Wehrmacht commissioned the production of some small ���shunter��� locomotives which could be used to position railway guns and was a component of the artillery units. For movement or heavy artillery on railcars often the WR360���s were used...

In WWII the Germans modified many freight and passenger locomotives for use in transporting troops and armor across the battlefield. Heavy steel plates were affixed to both sides of the locomotives to protect them from enemy attack, as these were slower...

These of armored trains became prevalent during WWII initially on the Eastern Front. Transport through occupied areas of Eastern Europe became dangerous due to partisan groups attacking advancing troops. The Germans considered armored trains a more...

A component of the armored trains which transported military equipment across the battlefield, these heavy flatcars were often seen loaded with tanks and trucks. They were placed securely between armored and cannon railcars for protection of the...

The Russian Empire placed a high value on armored trains as part of its ground force because their infrastructure at the time did not allow for the mass movement of men and equipment. The PL-37 was a single car equipped with cannons and armament to...

This German heavy armored railcar was a modification of German locomotive WR 550. It was encased in heavy armor and equipped with two 20mm artillery positions, one at each end of the unit. After capture by the Soviets, the towers were replaced by...

Item #313

Includes 4 USMC figures and USMC markings

Item #350 is a German tank destroyer

Item #351

Item #352

Kit includes PE, rope, springs and markings for the Russian, East German, Polish and Czech armies.

Kit consists of 674 parts on 15 sprues, 2 metal shells, 5 photo etched parts, 1 film part, hull, tracks and markings for the German Army. Incredibly detailed!

The BMP-1 was designed primarily to enhance troop combat mobility and offer armor protection to infantrymen fighting with tank support. Later the BMP-1 was upgraded to the BMP-3 with a 30mm automatic gun, a 100mm gun with moderate ballistics and a 7...

The ERA tile system covers 49 percent of the vehicle front and 85 percent of its sides. It is also provided with a spall liner in the fighting compartment, and the fuel tanks are given better protection against large calibermachine gun fire. This...

First of its kind in plastic kit form! In WWII, the Germans developed what is basically a tank turret mounted on an armored rail car. A front-mounted plow attached to the rail car was used to clear the rails of any debris or mines, while the turret...

Kit consists of 203 parts on 13 sprues plus photo etched details and markings for the German Army.

The LAV-R is an all-terrain, all-weather vehicle with night capabilities. This vehicle is be capable of safely uprighting overturned LAVs while minimizing additional damage. It has the tactical mobility to reach & recover/support disabled vehicles...

Kit consists of 238 parts on 9 sprues with USMC markings

There are 232 parts in light grey plastic, 8 rubber tires. Also includes photo-etch engine grill and USMC markings.

Item #375 - The ICV troop transport vehicle is capable of carrying 9 infantry soldiers and equipment. It requires a crew of two; a driver and a vehicle commander. It is known for its exceptional tactical mobility for full spectrum operations, it's...

<br /

Kit consists of 176 parts on 6 sprues plus a hull and vinyl tracks, 2 etched parts for engine cover and net, thread for towing cable and brass wire for handrail on turret. Markings are for Russian Army green camoflage and for Syrian Army in...

Kit consists of 176 parts on 5 sprues plus lower and upper hulls, a photo etched engine cover/dustproof net and vinyl tracks. Markings for Russian Navy Marines (Green camouflage as well as green/gray/sand brown camouflage). The PT-76 was a post WWII...

The Entwicklung series, more commonly known as the E- series, was a late-WWII attempt by Germany to produce a standardized series of tank designs. The E-25 designs, in the 25-50 ton weight class, were to replace all Panzer III and Panzer IV designs. This...

Kit consists of 130 parts on 9 sprues plus hull, photo etch part, and both early and late variants of vinyl & styrene tracks. Markings for the German Army.The E-10 was developed as a replacement of the Panzer 38(t). The 38(t) chassis was enlarged and...

The Centauro B1 tank destroyer is designed for reconnaissance and territorial defense tasks. The main mission is the protection of lighter vehicles and units of the Cavalry. It is not a reconnaissance vehicle, but a tank destroyer/wheeled tank. The...

Towards the end of WWII the Germans converted some Panzer IV tanks to Bergepanzer IV recovery vehicles. These heavy duty machines were used to recover damaged artillery and tanks from the battlefield. Only 36 Panzer IV tanks were actually converted. ...

In April 1940, the Germans converted some Panzer IVc and Panzer IVd tanks to bridgelayers to be used primarily in France and Belgium to forge the many rivers over which previous bridges had been destroyed. These were designated Panzer IVb and a total of...

The LAV-M carries an 81mm M252 mortar in the center of the vehicle and also has space for 90 rounds of ammunition. It carries 5 personnel: driver, commander and three-person mortar team. Kit consists of 237 parts on 6 sprues plus upper and lower hull and...

This is the Australian variant of the LAV personnel carrier. It is a highly mobile, eight wheeled amphibious armored vehicle used for reconnaissance and surveillance operations. The ASLAV has an eight wheeled configuration, is amphibious and has a...

New variant of the LAV, with GAU-12/U 25mm Gatling Gun for air defense use. Kit consists of 227 parts. Features: Drive train consisting of separate parts, upper and lower hulls with fine details, turret can swivel 360 degrees, infrared targeting sight...

Includes 218 plastic parts on 5 sprues plus upper hull, lower hull, upgraded turret, additional updated armor and tracks, 1 sheet of PE, a file sheet for winders and persicope lenses and towing cable. Markings for the Italian Army.

The differences between this kit and the M1126 variant are the newly tooled 141 parts on 6 sprues to reproduce the features for M1127, including 50cal. & M240 7.62mm machine guns, smoke launcher & four infantry figures. Kit consists of 440 parts on 15...

The Stryker Command Vehicle has been designed to perform command and control functions in support of Stryker-equipped brigades. It is very technologically advanced, using a video screen to monitor events on the battlefield and can obtain and relay...

The FSV of the Stryker series provides automated enhanced surveillance, target acquisition, target identification, target tracking, target designation, position location and communications functionality. Targets will be transmitted instantly to the...

The Stryker Anti-Tank Guided Missile Vehicle has an elevated TOW system and is able to fire TOW anti-tank missiles. Unlike the Stryker IAV, this variant is produced combat ready. Kit consists of 440 parts on 11 sprues, 46 photo-etched parts, rubber tires...

Item #402 includes 4 figures

Item #403 includes 4 figures

Item #404 includes 4 figures

Item #408 includes 3 crew figures

Includes 4 figures with M4, M4 with Scope, M239 SAW, and M203

* includes 4 figures