Glues-Cements-Adhesives

The perfect adhesive to fix all types of sand, gravel and rubble to diorama bases. This product can be applied to the surface using a brush or airbrush and drying can be accelerated using a hairdryer. Jar of 100mL

Extra thin plastic cement. Hold the parts together, apply the cement to the joint and it will draw itself into the gap by capillary action. Completely dries in 10 minutes. * SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via...

High strength acrylic glue. Specially designed to fix photo-etched or transparent parts comfortably without leaving any residue whatsoever. Jar 40mL. High strength acrylic glue. Specially designed to fix photo-etched or transparent parts...

Medium density and high strength cement for use in assembling plastic scale models. It is particularly useful for gluing large components that need a strong initial bond. Clean the contact surfaces before applying the product. This cement will allow you...

  High-strength cement for use in assembling plastic scale models. The consistency lies between that of Extra Thin Cement (AMM2025) and Medium Density Cement (AMM2038) Jar of 30 mL.It is particularly useful for gluing medium-sized components that...

  Blue-colour extra-thin cement for use in assembling plastic scale models. Jar of 30 mL.Hold the parts together, apply the cement to the joint and allow it draw itself into the gap by capillary action. Its blue colour stands out against the...

  Red colour extra-thin cement for use in assembling plastic scale models. Jar of 30 mL.Hold the parts together, apply the cement to the joint and allow it draw itself into the gap by capillary action. Its red colour stands out against the plastic...

The FIRST STEPS SET contains all the necessary materials for the assembly, masking, and decal application on your models, both for beginners and more experienced modelers. These products offer the highest quality and simplicity of use to ensure a perfect...

This product can be used to glue plastic, resin, photo-etch, some metals, and similar materials. Hold the pieces together for 10-15 seconds to ensure proper bond. The black colour makes the glue highly visible, once dry the black cyanoacrylate can be...

Debonder can be used on a wide range of surfaces including plastic, resin, and photo etch. Simply apply using a brush or a pipette onto the glue and let it act for about 45 seconds. Then clean the surface with a cloth. If necessary, these steps can...

Activator21 is specially formulated to accelerate the drying of cyanoacrylate glue. It has two systems of application: it can be used with the diffuser quickly and comfortably or with the brush inside for greater precision. This allows an almost...

It provides an extremely strong bond and dries in only 10-15 seconds. This product can withstand temperatures of up to 150 ºC (300 ºF) approximately, and forces of up to 180 kg/cm2 (2500 psi). It can be applied directly from the bottle or by using a...

This versatile product is easy to use and features a dispenser for precise application. Simply apply the product over the cyanoacrylate to speed up the cure time. The application process can be reversed: apply Magicdust 21 first and then the CA glue,...

This product Sticks like Glue, but is handy like Tape!  Thick layer of adhesive, approx. 1mm, allows joining rough, smooth, and uneven surfaces.  Super Fix Glue Strips leave no residue, and is ideal for permanent or removable jobs.  Use...

Touch-N-Flow is the easy-to-handle, lightweight applicator for the precise control of liquid plastic cements and C/A activators. Save your brushes for painting, with Touch-N-Flow you can: Join seams with a continuous application- no stops to refill a...

NOTE - the Touch-N-Flow and filler bottle are NOT included. They are shown only for illustration purposes of the use of the work base. Now holds everything you need to keep your Touch-N-Flow and Solvent Cement ready for use. No more spills! Holds a...

A New Take on the C/A applicator! Draw thin lines of liquid C/A glue with a capillary action designed applicator that fits into our Micro Pin Vice handle. Ergonomic design with slight angle provides all the comfort needed for fatigue-free...

1/2 oz. Bottle with 25 and 27 gauge interchangeable steel tubes and protector cap.

1/2 oz. Bottle with 20 gauge flexible poly tube allows precise control of thin liquids into hard to reach places.

Includes everything needed to use the Touch-N-Flow system.   NOTE - the picture shows the liquid cement included as Ambroid Pro Weld, however the actual liquid cement included with this item may vary depending on availability.SURFACE SHIPPING...

* SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground shipping. Purchasing this item will result in your entire order being only eligible for either UPS Ground or USPS Parcel Post shipping. US customers located outside...

It is the glue of the type keep together the parts and parts, run into the gap. Limonene type, raw materials extracted from citrus natural ingredients has become based, does not have a pungent odor.* SURFACE SHIPPING ONLY (US Customers) - This item can...

* SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground shipping. Purchasing this item will result in your entire order being only eligible for either UPS Ground or USPS Parcel Post shipping. US customers located...

Black color comes in Mr.CEMENT SP. It colors application in black as you can see where you apply on. For plastic plate craft, applied surface turned in lack so that you can measure precisely. It is a kind of pigment that is covered by coating paint. *...

�?� HG liquid 10g / 2 this �?� HG powder / 4.5g �?� softener / 2g It is a moment of bonding putty outstanding performance in molding processing parts of the model in general adhesion garage kits and plastic model, such as figures, off junction line,...

This item helps accelerate the hardening speed of instant adhesives by applying it on the joint surface beforehand. This is an alcohol type promoter, so it can be used without corroding the painted surface. * SURFACE SHIPPING ONLY (US Customers) - This...

Instant adhesive with excellent shock resistance, most suitable for metal parts Very effective when used for etching New package design: can be opened without a pin * SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground...

UsageA solvent-based cement suitable for plastic model kits only. The product is a low viscosity version of Humbrol Poly Cement to enable application by brush.SubstrateCommon plastics used to manufacture model kits including polystyrene and ABS. The...

UsageA solvent-based polymer solution for use as an adhesive on clear plastic parts without the risk of the 'frosting' effect sometimes seen using traditional glues and for making small windows or translucent areas of 3mm or lessSubstrateCommon...

There is nothing quite like Micro Weld styrene solvent cement. You will find that application is very much different from and easier than, other types of cement. It is much more forgiving than other types of cement are, stronger when dry, and will not...

If there was ever a modeler’s secret, this is it. Micro Kristal Klear can do so many things that can make a big difference in the appearance of your models. First, Micro Kristal Klear is a liquid that can be used to form very real looking small...

Micro Liquidtape is a liquid adhesive that when applied to one side of a part and allowed to dry, can be pressed on to another clean part where it will stick firmly enough for a display model. You can take it apart again and again as long as they stay...

A typical plastic model adhesive works with the welding effect. This means that it dissolves the plastic and thus bonds the areas very firmly together. Revell Contacta Liquid is a super-thin liquid adhesive that is applied with a brush. The adhesive is...

Revell Contacta in the tube is gel-like. This has the advantage that large model parts can be precisely aligned without drying out immediately. Special properties: With plastic welding effect Gel-like consistency of the adhesive Suitable for aligning...

Revell Contacta Professional for precise gluing. With the needle-fine cannula, micro-precise bonding can be carried out on tiny details and on the edges of transparent parts. Special properties: With plastic welding effect Liquid consistency of the...

Revell Contacta Clear is a special crystal clear adhesive for model making. It is a water-based adhesive which is suitable for various types of plastics in general. When dried, it has a high transparency, so that it can be used mainly for bonding clear...

INSTA-CURE? has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At...

INSTA-CURE? has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At...

INSTA-CURE+? is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas,...

INSTA-CURE+? is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas,...

MAXI-CURE? extra thick CA is the best CA for most plastics, including GE?s Lexan MAXI-CURE? is the best choice for plastic model assembly. When used with INSTA-SET?, it works better than any putty for modifying or filling voids. It can be carved with a...

MAXI-CURE? extra thick CA is the best CA for most plastics, including GE?s Lexan MAXI-CURE? is the best choice for plastic model assembly. When used with INSTA-SET?, it works better than any putty for modifying or filling voids. It can be carved with a...

IC-GEL? is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE?; IC-Gel?, however, can be applied to a vertical surface and will stay in...

INSTA-FLEX? flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX? does not turn brittle and remains clear, even if accelerated with INSTA-SET?. It has superior shock resistance. Although not as...

SUPER-GOLD? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white foam; therefore, they can be used in the building of...

SUPER-GOLD? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white foam; therefore, they can be used in the building of...

SUPER-GOLD+? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white foam; therefore, they can be used in the building of...

SUPER-GOLD+? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white foam; therefore, they can be used in the building of...

FOAM-CURE�?� is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it�??s curing...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is normally used to cure the CA that flows from joints when...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is normally used to cure the CA that flows from joints when...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is normally used to cure the CA that flows from joints when...

UN-CURE? debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE? will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off...

QUIK-CURE�?�5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE�?� shouldn�??t be used in areas that are subject to long-term...

MID-CURE�?� 15 min.epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE�?� in most applications. MID-CURE�?� is our most flexible epoxy and is ideal for gluing to...

SLOW-CURE�?� 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE�?� can be used for bonding if you�??re willing to wait overnight. Fillers...

FINISH-CURE�?� 20 min.epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE�?� can be sanded the easiest of all...

For use over the standard #312 top. Can be used with all thicknesses of CA except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application.

For use over the standard #312 top. it allows our thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.

For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone.

For use with BSI's Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas.

Two foot length of tubing can be cut off to any length (usually 2"). With one end cut at a 45� angle, can be inserted 1/8" into Pocket CA top and into #312 top if it is cut down an additional 3/64". For thin CA.

Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.

Replacement colored cap that fits over the #312 top.

Replacement combination of top and screw-on cap that has a built-in pin for Pocket CAs. Will fit on Pocket CA bottles only.

Regular Tip Non-clog 6" long pipette for the application of gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end compressed, like an eyedropper.

Fine Tip Non-clog 6" long pipette for the application of thin CAs. Can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the applicator for two weeks.

* SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground shipping. Purchasing this item will result in your entire order being only eligible for either UPS Ground or USPS Parcel Post shipping. US customers located...

* SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground shipping. Purchasing this item will result in your entire order being only eligible for either UPS Ground or USPS Parcel Post shipping. US customers located outside...

* SURFACE SHIPPING ONLY (US Customers) - This item can only be shipped via surface/ground shipping. Purchasing this item will result in your entire order being only eligible for either UPS Ground or USPS Parcel Post shipping. US customers located...

CEMENT FOR PLASTIC MODELS is specially formulated for joining all polystyrene plastics. CEMENT FOR PLASTIC MODELS can be used in the construction of plastic model kits and may also repair many common household products made of polystyrene or ABS...

Testor Cement is a wonderful choice when needing glue. We have a wide range of glues that cover almost every gluing need from plastic to metal and even wood. This glue is best used for Polystyrene & ABS plastic. Quick drying cement for plastic...