Flying Leathernecks Decals / Orion Scale Models

This is a CD which includes approximately 387 high res photos of the AH-1W Cobra. CD is divided into six sections: Pilot's Cockpit Gunner's Cockpit Fuselage Hellfire Missile In-flight Photos Afghanistan

Includes 604 high resolution walk around photos.

The FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR. Designed for the Dream Model AH-1Z kit

Set of four (4) 3D printed launchers The LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.

Set of four (4) 3D printed launchers The LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft.

FL32003 'Hornets Swarm' US Marine Corps F/A-18A/C in Combat Part I This two sheet set features markings for two F/A-18A's, one F/A-18A+ and three F/A-18C aircraft as they appeared during deployments in support of combat operations. VMFA-333...

  VMFA(AW)-533 BuNo 164959 Operation Iraqi Freedom, Al Asad Air Base, Iraq 2008 VMFA(AW)-224 BuNo 164699 MCAS Iwakuni, Japan 2009 VMFA(AW)-332 BuNo 164870 Operation Deny Flight, Aviano Air Base, Italy 1994 - One of several F/A-18D's from the...

Mk-76 practice bombs (6 per pack) These new 3D printed bombs come ready to paint and install. Some very light clean up may be necessary at the aft end of the fins to remove any trace of the printing supports. Simply paint FS35109 Blue and...

This set includes two (2) Mk-83 1000lb bombs, two (2) BSU-85 fins and two (2) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs. The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was...

AN/ALQ-144, ready to paint and attach to your model. This set includes one (1) AN/ALQ-144. For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10

This set of pylons corrects the inaccurately shaped pylons included in the Academy kit. Each set is 3D printed to ensure the best quality possible, as well as to minimize the work required to prepare them for installation on your model. An added...

This set contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D. These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532, as well as F/A-18A++ aircraft after...

This set contains all of the parts necessary to convert the Academy 1/32 F/A-18D into an ATARS Configured aircraft. The Advanced Tactical Airborne Reconnaissance System (ATARS) had its combat debut in 1999 with VMFA(AW)-332 during Operation Allied Force...

This set includes two (2) Mk-83 1000lb bombs, two (2) Conical fins and two (2) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs. The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was...

Includes parts to build 6 bombs.

This set includes two (2) Mk-83 1000lb bombs with the Thermal Protective coating, two (2) BSU-85 fins and two (2) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during...

This set includes two (2) Mk-83 1000lb bombs with the Thermal Protective coating, two (2) Conical fins and two (2) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC...

  This set includes four (4) highly detailed ADU-703 adapters with BRU-32 bomb racks for use on the Tamiya, Revell and Trumpeter 1/32 F-14A/B/D kits. Modification to the kit weapons rails will be necessary. Drawings with measurements on where to...

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following : M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of...

  Set of four (4) 3D printed launchers The LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.

  Set of four (4) 3D printed launchers In May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1. In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2. By...

Set of four (4) 3D printed launchers In September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4. In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5. The...

Set of four (4) 3D printed launchers In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6. Over the course of the next several years, numerous AAC's changed the designation of the launcher to...

This set contains one (1) pod. The AN/ALQ-164 Defensive Electronic Countermeasures (DECM) Pod was used exclusively and frequently by the US Marine Corps AV-8B Harriers during Operation Desert Storm. While limited in its use, the pod is still carried...

This set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.

AN/ALQ-144, ready to paint and attach to your model. This set includes one (1) AN/ALQ-144. For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10

This set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft. Pods are 3D...

This set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts.

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed.

Set of four (4) 3D printed launchers In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6. Over the course of the next several years, numerous AAC's changed the designation of the launcher to...

This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean...

This set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene. Parts come as shown in photo. Very light sanding...

This set includes two (2) XM158A1 Rocket Launchers. The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount

This set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.

8.5 x 11 inch sheet featuring three KC-130J aircraft from VMGR-252 and VMGR-352. Designed for Italeri kit with Attack Squadron conversion sets.. Screen printed by Microscale

The sheet covers 10 AH-1W's and is designed to fit both the Italeri and Kittyhawk kits. Options include the following aircraft :HMLA-167 -165362 TV29 (Operation Iraqi Freedom, October 2005)163932 TV32 (MCAS New River, NC June 2018)165446 TV42 (Live...

FL48019 Marine Skid Kid Zulu's- 13 options, at least one from each HMLA and a few attached to MEU's.- Stencils for the LAU-68 and LAU-61 Rocket pods.Multiple Marines from across the Skid Kid community assisted with reference photos and information...

After our amazingly successful release of almost the same sheet in 1/35 scale, we have scaled down the markings for the Kittyhawk kit. FL48019 Marine Skid Kid Zulu's- 13 options, at least one from each HMLA and a few attached to MEU's.- Stencils for the...

AN/ALQ-144, ready to paint and attach to your model. This set includes one (1) AN/ALQ-144. For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10

This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Designed for the Kittyhawk kit.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come...

Set FL48-8013 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and F/A-18B.These pylons are correct for F/A-18A/B aircraft with BuNo's 161353 thru 163175.While the locating holes are designed to fit...

Set FL48-8014 contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D. These pylons are correct for F/A-18A+ thru D aircraft with BuNo's 163427 thru 163782. While the locating holes are...

This set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft. Pods are 3D...

This set includes six Thermally Protected Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs. Accurately reproduced using personal measurements and photos of the real item...

This part is designed to be used with Bullseye Model Aviation Decal Sheet 48-017 and Furball Aero-Design Decal Sheet 48-076 when building the VF-14 and VF-32 options.

This set provides correctly sized and detailed wing fold hinge covers for the Kinetic or Italeri (Kinetic plastic) EA-6B Prowler kits. A quick and light sanding of one edge to remove the support nibs is all that is needed. Simply pop into place and glue.

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed.

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following : M904 Nose Fuze Mk-43 TDD MXU-735 Solid Nose Plug Bombs come as shown in the photo. Light sanding may be needed on the aft...

Set of four (4) 3D printed launchers The LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.

Set of four (4) 3D printed launchers In May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1. In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2. By 1972, the...

Set of four (4) 3D printed launchers In February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket. The LAU-7A/A was used interchangeably with the Aero-3B on USAF...

Set of 4 LAU-7 Missile Launchers designed to be used on the Zoukei-Mura F-4J. With little modification, can also be used on the Academy F-4B/N/J, Hasegawa F-4B/N/J and Tamiya F-4B.

Set of 4 LAU-7 Missile Launchers designed to be used on the Zoukei-Mura F-4J. With little modification, can also be used on the Academy F-4J and Hasegawa F-4J

Set of four (4) 3D printed launchers In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6. Over the course of the next several years, numerous AAC's changed the designation of the launcher to...

Set of four (4) 3D printed launchers The LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft.

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile. This set includes 4 launchers and can be used on a variety of USN, USMC and USAF aircraft from the 50's and 60's. Each launcher is 3D printed and are easily removed...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration. This set includes...

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the...

Set includes four (4) launchers Used to carry and launch AIM-9X and AIM-120B/C

Set includes four (4) launchers. Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage

Set includes four (4) launchers Used for early F/A-18E/F

Set includes four (4) launchers Used for early F/A-18E/F

This set provides 24 M904 nose fuses that will help enhance those kit supplied bombs at a reasonable cost. Parts are 3D printed and come as shown in the photo.

This set provides 24 MXU-735 Solid Nose Plugs and will provide another option for your kit supplied bombs at a reasonable cost. Parts are 3D printed and come as shown in the photo.

This set provides 24 Mk-43 TDD (Target Detecting Device) and will provide another option for your kit supplied bombs at a reasonable cost. Parts are 3D printed and come as shown in the photo.

This set includes four (4) LAU-33 dual 5.00" Rocket Launchers with empty tubes. Used by the F-4 Phantom, F-8 Crusader, OV-10 Bronco

This set contains two (2) LAU-10 launchers with full length hollow tubes.

This set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene. Parts come as shown in photo. Very light sanding...

This set includes two (2) XM158A1 Rocket Launchers. The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount

5.5 x 8.5 inch sheet and designed for the Italeri 1/72 C-130 and Attack Squadron / Brengun KC-130J conversion parts.Features markings for 4 aircraft, including a Harvest Hawk option from VMGR-352. Printed by Microscale.

For the Trumpeter kit with the Fisher A3243/A3240 Conversions

For the Trumpeter kit

For the Academy F-16 kit

For the Academy F-18 kit

For the Academy F-16D/I kit

For the Wolfpack WPD32038 kit

For the Academy kit

For the Revell kit

For the Kitty Hawk kit

For the Kitty Hawk kit

For the Italeri kit

For the Revell kit

For the Hasegawa kit

For the Kitty Hawk kit

For use with the Academy F-15E/F-15I kits

For use with the AMK F-14D Tomcat kit

For use with the Academy kit

  For use with the Kinetic kit

For use with the Tamiya and Academy kits

AN/AAQ-28 UTENING Pod FUR/TV windows. Cut in blue and yellow holographic vinyl.

AN/AAS-38 and AN/ASQ-173 FLIR/Designator lens. Cut in holographic blue and yellow vinyl and designed for the Academy F/A-18 kits. Enough for six aircraft.

AN/AAQ-13, AN/AAQ-14 and AN/AAQ-33 FUR/TV/Designator lens. Cut in holographic blue and yellow vinyl. Designed to fit the pods in the Academy F-15E/I kits and Hasegawa Weapons Set E. Enough for six of each pod.