Flying Leathernecks

Set includes four (4) launchers Used for early F/A-18E/F

Set includes four (4) launchers. Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage

This set includes two (2) XM158A1 Rocket Launchers. The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified...

This set contains two (2) LAU-10 launchers with full length hollow tubes.

This set includes four (4) LAU-33 dual 5.00" Rocket Launchers with empty tubes. Used by the F-4 Phantom, F-8 Crusader, OV-10 Bronco

  For use with the Kinetic kit

For use with the Kinetic kit This set contains pre-cut self adhesive vinyl Det Cords for the canopy. Transfer tape included and pre-attached.

For use with the Zvezda kit This set contains pre-cut self adhesive vinyl Det Cords for the canopy. Transfer tape included and pre-attached.

This set provides 24 Mk-43 TDD (Target Detecting Device) and will provide another option for your kit supplied bombs at a reasonable cost. Parts are 3D printed and come as shown in the photo.

This set provides 24 MXU-735 Solid Nose Plugs and will provide another option for your kit supplied bombs at a reasonable cost. Parts are 3D printed and come as shown in the photo.

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies...

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile. This set includes 4 launchers and can be used on a variety of USN, USMC and USAF aircraft from the 50's and...

Set of four (4) 3D printed launchers The LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft.

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed.

Set of 4 LAU-7 Missile Launchers designed to be used on the Zoukei-Mura F-4J. With little modification, can also be used on the Academy F-4B/N/J, Hasegawa F-4B/N/J and Tamiya F-4B.

Set of four (4) 3D printed launchers In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6. Over the course of the next several years,...

Set of four (4) 3D printed launchers In February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket. The...

Set of four (4) 3D printed launchers In May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1. In January of 1971, AAC-537-1 introduced the...

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following : M904 Nose Fuze Mk-43 TDD MXU-735 Solid Nose Plug Bombs come as...

8.5 x 11 inch sheet featuring three KC-130J aircraft from VMGR-252 and VMGR-352. Designed for Italeri kit with Attack Squadron conversion sets.. Screen printed by Microscale

AN/AAQ-13, AN/AAQ-14 and AN/AAQ-33 FUR/TV/Designator lens. Cut in holographic blue and yellow vinyl. Designed to fit the pods in the Academy F-15E/I kits and Hasegawa Weapons Set E. Enough for six...

For use with the AMK F-14D Tomcat kit

For use with the Academy F-15E/F-15I kits

For the Hasegawa kit

This set includes six Thermally Protected Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs. Accurately reproduced...

This set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y,...

Set FL48-8013 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and F/A-18B.These pylons are correct for F/A-18A/B aircraft with BuNo's 161353...

AN/ALQ-144, ready to paint and attach to your model. This set includes one (1) AN/ALQ-144. For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10

The sheet covers 10 AH-1W's and is designed to fit both the Italeri and Kittyhawk kits. Options include the following aircraft :HMLA-167 -165362 TV29 (Operation Iraqi Freedom, October 2005)163932...

After our amazingly successful release of almost the same sheet in 1/35 scale, we have scaled down the markings for the Kittyhawk kit. FL48019 Marine Skid Kid Zulu's- 13 options, at least one from...

FL48019 Marine Skid Kid Zulu's- 13 options, at least one from each HMLA and a few attached to MEU's.- Stencils for the LAU-68 and LAU-61 Rocket pods.Multiple Marines from across the Skid Kid...