Sprue Brothers Models Private Label Products

- 2 x 2oz empty natural cylinder round plastic bottles with dispensing cap- Great for storing your thinners, cleaning fluids, flat/gloss cotes, etc.- DIspensing cap allows you to easily dispense the...

- Keep your modelling area organized!- Keep your model parts together- Ideal for spill containment- Size: 15.5 inches x 10.5 Inches x 1 inch deepNOTE - only includes the tray

Fine Tip Non-clog 6" long pipette for the application of thin CAs. Can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the...

Replacement combination of top and screw-on cap that has a built-in pin for Pocket CAs. Will fit on Pocket CA bottles only.

Regular Tip Non-clog 6" long pipette for the application of gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end...

Two foot length of tubing can be cut off to any length (usually 2"). With one end cut at a 45� angle, can be inserted 1/8" into Pocket CA top and into #312 top if it is cut down an additional 3/64"...

Replacement colored cap that fits over the #312 top.

Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.

For use with BSI's Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas.

For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by...

For use over the standard #312 top. Can be used with all thicknesses of CA except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application.

For use over the standard #312 top. it allows our thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.

FINISH-CURE�?� 20 min.epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and...

SLOW-CURE�?� 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE�?� can be used for ...

MID-CURE�?� 15 min.epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE�?� in most applications. MID-CURE�?� is...

QUIK-CURE�?�5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE�?� shouldn�??t...

UN-CURE? debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE? will dissolve the CA in about a minute. Apply on bonded skin and...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is...

INSTA-SET? is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET? in a spray bottle is...

FOAM-CURE�?� is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like...

SUPER-GOLD+? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack...

SUPER-GOLD+? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack...

INSTA-CURE+? is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together...

SUPER-GOLD? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white...

IC-GEL? is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE?; IC-Gel?, however,...

SUPER-GOLD? is our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD??s do not attack white...

INSTA-CURE+? is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together...

INSTA-FLEX? flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX? does not turn brittle and remains clear, even if accelerated with...

MAXI-CURE? extra thick CA is the best CA for most plastics, including GE?s Lexan MAXI-CURE? is the best choice for plastic model assembly. When used with INSTA-SET?, it works better than any putty...

INSTA-CURE? has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together...

MAXI-CURE? extra thick CA is the best CA for most plastics, including GE?s Lexan MAXI-CURE? is the best choice for plastic model assembly. When used with INSTA-SET?, it works better than any putty...

INSTA-CURE? has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together...

- 3 x 4oz empty natural cylinder round plastic bottles with dispensing cap- Great for storing your thinners, cleaning fluids, flat/gloss cotes, etc.- DIspensing cap allows you to easily dispense the...

- 6 x 1/2oz empty glass mixing bottle with caps- Uses include mixing or thinning paint

Made of shatterproof, low-density polyethylene. Total length is 15.4cm. Stem diameter is 6.6mm. Contains 12 pipettes

This is a pair of medium weight cotton modeling gloves. These gloves will help you keep your fingerprints and bodys oils off of the model, help keep the model clean, help avoid damage to delicate...